Our refill cores have the same geometry as the Bambu refills.
Ambrosia Filament's line of PLA is part of our Low Calorie line of filament, no additives just butter smooth printing.
Feed your Printer the Filament of the Gods.
Derived from 100% Virgin Grade-A Non-Toxic pellets. Manufactured to a tighter than standard tolerance (+/- 0.03mm) you'll experience consistent extrusion throughout the spool.
PLA is most hobbyist makers material of choice for 3D printing. A bio-degradable plastic derived from renewable resources (such as corn... I know we say our filament is low calorie, but don't eat it - your printer is the only machine that should injest our filament!) it is one of the easiest materials to print with, with a relatively low melting point and is able to be printed without a heated bed. Printing with PLA is typically odorless, or when it smells gives of a 'sweet' aroma, and emits less harmful fumes than some other 3D printing materials, making it a safer option for enclosed spaces without proper ventilation.
Arrives to you in a cardboard box, with filament wound in a cardboard spool, vacuum sealed with a desiccant bag.
Derived from 100% Virgin (Grade-A) non-toxic pellets
Diameter: 1.75mm (+/-0.03mm)
Filament Net Weight: 1KG
Spool Weight: 130G
The glue holding the filament spool together is rated for an environment of 70C (158F). If using a filament dryer or require the filament spool by placed in an environment exceeding this temperature, we recommend printing a spool clip (here).
Ambrosia Filament's Recommended Print Settings for our PLA filament:
Attribute
Accepted Value(s) [Our Recommended Value]
Extruder Temperature
190-220 Degrees Celsius [210]
Heated Bed
0-65C Degrees Celsius [60]
Build Surface
PEI, Glass, Painters Tape, Buildtak, or similar surface [Smooth PEI]
Cooling Fan
50-100% range varies by cooling capabilities
Environmental Temperatures
15-40C [25C]
Soluble Support Materials
PVA, BVOH
Technical Specifications for our PLA Filament:
Physical Properties
Test Methodology
Values
Density
ISO1183
1.25-1.26 g/cm^3
Melt Flow Rate (250C/2.16KG)
ISO 1133
4-8 g/10min
Mechanical Properties
Test Methodology
Values
Tensile Strength
ISO 527
45-49 Mpa
Elongation at break
ISO 527
13-15.5%
Flexural Modulus
ISO 527
1000-1100 Mpa
Flexural Strength
ISO 178
69-75 Mpa
Impact Strength
ISO 180
4.5-5 KJ/m^2
Thermal Dynamic Properties
Test Methodology
Values
HDT@ 0.455 MPa(66 psi)
ISO 75
53C
Continuous Use Temperature
IEC 60216
50C
Filament can absorb moisture easily. To prevent moisture absorption and contamination, the packing of filament should be kept sealed and in an airtight container with desiccant.
Disclaimer: Filaments, including this product, may emit toxic fumes (Volatile Organic Compounds) into the air when heated. Please consider this and follow safety protocols when printing with Ambrosia Filament. Only use in a well ventilated area, with proper respiration equipment. Technical Data and Safety Data contained attempts to summarize to the best of our knowledge the properties, health and safety information of the specified product and how to handle it. However, it is your responsibility to determine the suitability for use. Ambrosia Filament provides no warranty and assumes no responsibility or liability for the information contained and expressly disclaims that the information is a representation or guarantee of the specifications, properties, or health and safety data.
Yes, we provide free standard ground shipping* on all orders over $350. For orders under $350, our standard shipping cost applies, which will be shown at checkout.
*Up to 20.99 off per shipment.
If you're not completely satisfied with your purchase, you can return it within 30 for a full refund minus shipping costs and restocking fees, unless item is made to order then the item is non-returnable. Please ensure the item is unused and in its original packaging.
We use 100% Eco Friendly Plant Based plastic, 90 % of our colors Made in the USA to the exception of our rainbow and gradiants which we buy from Asia since no USA manufacturer makes rainbow and gradiants. We use Made in America parts in our 3D printer farm, Mostly Microswiss and Slice Enginering parts.
When you choose OJAI3D you get exactly what you pay for we value quality over cost and choose to provide better quality instead of maximizing profit. We make very little on each product in order to offer affordable quality product made in America while also supporting a neurodivergent business model, We are a neurodivergent business employing autistic workers afterall.
